CCNA 1 module 8 Exam
- -backbone cable
- horizontal cable
- patch cable
- work area cable
2 What is a primary role of the Physical layer in transmitting data on the network?
- -create the signals that represent the bits in each frame on to the media
- provide physical addressing to the devices
- determine the path packets take through the network
- control data access to the media
3 Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?
- coax cable
- rollover cable
- -crossover cable
- straight-through cable
4 What is considered a benefit of wireless as a media choice?
- -more host mobility
- lower security risks
- reduced susceptibility to interference
- less impact of the surroundings on the effective coverage area
5 In LAN installations where potential electrical hazards or electromagnetic interference may be present, what type of media is recommended for backbone cabling?
- coax
- -fiber
- Cat5e UTP
- Cat6 UTP
- STP
6 In most business LANs, which connector is used with twisted-pair networking cable?
- BNC
- RJ-11
- -RJ-45
- Type F
7 What is a possible effect of improperly applying a connector to a network cable?
- Data will be forwarded to the wrong node.
- -Data transmitted through that cable may experience signal loss.
- An improper signaling method will be implemented for data transmitted on that cable.
- The encoding method for data sent on that cable will change to compensate for the improper connection.
8 When is a straight-through cable used in a network?
- when connecting a router through the console port
- when connecting one switch to another switch
- -when connecting a host to a switch
- when connecting a router to another router
9 Which OSI layer is responsible for binary transmission, cable specification, and physical aspects of network communication?
- Presentation
- Transport
- Data Link
- -Physical
10 An installed fiber run can be checked for faults, integrity, and the performance of the media by using what device?
- light injector
- -OTDR
- TDR
- multimeter
11 Which characteristics describe fiber optic cable? (Choose two.)
- -It is not affected by EMI or RFI.
- Each pair of cables is wrapped in metallic foil.
- It combines the technique of cancellation, shielding and twisting to protect data.
- It has a maximum speed of 100 Mbps.
- -It is the most expensive type of LAN cabling.
12.Which method of signal transmission uses radio waves to carry signals?
- electrical
- optical
- -wireless
- acoustic
13.Which of the following is a characteristic of single-mode fiber-optic cable?
- generally uses LEDs as the light source
- relatively larger core with multiple light paths
- less expensive than multimode
- -generally uses lasers as the light source
14.What are three measures of data transfer? (Choose three.)
- -goodput
- frequency
- amplitude
- -throughput
- crosstalk
- -bandwidth
15.With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
- -the magnetic field around the adjacent pairs of wire
- the use of braided wire to shield the adjacent wire pairs
- the reflection of the electrical wave back from the far end of the cable
- the collision caused by two nodes trying to use the media simultaneously
16. With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
- -the magnetic field around the adjacent pairs of wire
- the use of braided wire to shield the adjacent wire pairs
- the reflection of the electrical wave back from the far end of the cable
- the collision caused by two nodes trying to use the media simultaneously
17. Which fiber connector supports full duplex Ethernet?
- opt1
- opt2
- -opt3
- opt4
18. What characteristic of UTP cable helps reduce the effects of interference?
- the metal braiding in the shielding
- the reflective cladding around core
- -the twisting of the wires in the cable
- the insulating material in the outer jacket
0 Comments
